Download Free Testking CCIE 350-025 Dumps | Latest Cisco 350-025 Certification Exams

Testking CCIE 350-025

CCIE Service Provider Dial : 350-025 Exam
Question: 1
What command is used to set the length of time a non-ISDN interface stays down after a call has been completed or has failed and before it is available to dial again?

A. Dialer enable-timeout
B. Dialer holddown
C. Dialer fast-idle
D. Dialer idle-timeout
E. Dialer wait-for-carrier-time
Answer: A Question: 2
interface Dialer1
ip address 1.1.1.1 255.255.255.0
encapsulation ppp
dialer remote-name Smalluserdialer string 4540
dialer pool 3
dialer-group 1

What statement about this configuration is true?

A. This interface is configured for legacy DDR and therefore cannot be used for dialer profiles.
B. This interface is a logical interface whose configuration is only used for inbound calls on physical interfaces in pool 3.
C. This logical interface belongs to a group of physical interfaces in group 1.
D. This configuration is not valid because it is missing the “dialer in-band” command.
E. This interface will use the name Smalluser instead of the router’s hostname for authentication purposes when connecting to the remote peer.
F. None of the above
Answer: F Question: 3
To have the router verify a called-party number in the incoming setup message for an ISDN BRI
call:

A. Use isdn tei first-call
B. Include ldn on spid number line
C. Use isdn answer1
D. Use isdn caller
Answer: C Question: 4
The purpose of the dialer fast-idle command is:

A. To decrease the amount of time that an interface is kept down before the next call can be placed – By default, DTR is held low for five seconds.
B. To specify the amount of time that an interface can remain idle before being disconnected when new outbound calls need to be made
C. To decrease the interdigit delay between DTMF tones when placing a call
D. To increase the rate at which disconnected interfaces become available for new outbound calls

Page 1 of 56

Exam Name: CCIE Service Provider Dial
Exam Type: Cisco
Exam Code: 350-025 Total Questions: 203

E. To specify the regular idle timeout for high speed non-async interfaces
Answer: B Question: 5
On a Cisco router with an external modem, what EIA 232 signal will be received by the access server to indicate the presence of an incoming call?

A. Request To Send
B. Clear To Send
C. Data Terminal Ready
D. Data Set Ready
E. Loopback
Answer: D Question: 6
While entering commands on a console, the break key is pressed accidentally and the router reboots. What action could disable this problem?

A. In configuration mode, enter disable break.
B. In configuration mode, enter no service break. C. Change the configuration register.
D. Replace the router – this is an invalid response to pressing the break key when past 60
seconds after boot.
Answer: C Question: 7
The network administrator has forgotten the enable password of the router. Luckily, no one is currently logged into the router, but all passwords on the router are encrypted. What should the
administrator do to recover the enable password?

A. Call the Cisco Technical Assistance Center (TAC) for a special code that will erase the existing password.
B. Reboot the router, press the break key during bootup, boot the router into ROM monitor
mode, and modify the configuration register so that the current configuration is ignored during normal bootup
C. Reboot the router, press the BREAK key during bootup, and boot the router into ROM Monitor mode to erase the configuration, and re-install the entire configuration as it was
saved on a TFTP server.
D. Erase the configuration, boot the router into ROM Monitor mode, press the BREAK key, and overwrite the previous enable password with a new one.
Answer: B Question: 8
The configuration register does NOT retain settings for:

A. An enabled ‘Break’ key B. The console baud rate C. The boot method
D. An enabled AUX port

Answer: D

Page 2 of 56

Exam Name: CCIE Service Provider Dial
Exam Type: Cisco
Exam Code: 350-025 Total Questions: 203

Question: 9
Look at the router configuration above. If this router has a configuration-register setting of 0×102, select the proper boot sequence:

A. The router will try to use the image “rsp-isv-mz.112-8.P” on slot 0, then attempt to boot from a network server, and finally boot from ROM.
B. The router will try use the image “rsp-isv-mz.112-8.P” on slot 0, then attempt to boot from any other valid image in flash, and finally boot from ROM.
C. The router will try to use the image “rsp-isv-mz.112-8.P” on slot 0, and then it will boot from
ROM.
D. The router will try to use the image “rsp-isv-mz.112-8.P” on slot 0, and then attempt to boot from a network server.
Answer: A Question: 10
What effect will this configuration command have?line vty 0 4no password vtypassword

A. All telnet connections to the router will be denied.
B. Only one telnet connection at the router will be allowed at a time.

Free download?testking CCIE 350-025

Free download?pass4sure CCIE 350-025

PassGuide Cisco Braindumps-Buy Best Cisco Practice Exam,high-quality and low-price ,100% Guarantee to Pass , contact ,Mail:Sales@passguide.com

PassGuide Cisco Braindumps Free Downloads

Type	Exam Bible	New Questions & Answers	Latest Updated	Download link
	All Cisco 's Exam Pack	589	1 days ago	PassGuide Cisco