Cisco Certification Training

CCIE Cisco Certified Internetworking Expert Exam:

Exam Number/Code: 350-001
Exam Name: CCIE Cisco Certified Internetworking Expert
Questions and Answers: 315 Q&As
Price: $120.00
Update Time: 2008-5-21

“CCIE Cisco Certified Internetworking Expert”, also known as 350-001 exam, is a Cisco certification.
Preparing for the 350-001 exam? Searching 350-001 Test Questions, 350-001 Practice Exam, 350-001 Dumps?

Free 350-001 Demo Download

TestInside offers free demo for 350-001 exam ( CCIE Cisco Certified Internetworking Expert). You can check out the interface, question quality and usability of our practice exams before you decide to buy it. We are the only one site can offer demo for almost all products.
1. Two routers configured to run BGP have been connected to a firewall, one on the inside interface, and one on
the outside interface. BGP has been configured so the two routers should peer, including configuring the correct
BGP session endpoint addresses and the correct BGP session hop count limit (eBGP multihop). What is a good
first test to see if BGP will work across the firewall?
A. Attempt to telnet from the router connected to the inside of the firewall to the router connected to the outside of
the firewall. If telnet works, BGP will work, since telnet and BGP both use TCP to transport data.
B. Ping from the router connected to the inside interface of the firewall to the router connected to the outside
interface of the firewall. If you can ping between them, BGP should work, since BGP uses IP to transport packets.
C. There is no way to make BGP work across a firewall without special configuration, so there’s no simple test
that would show you if BGP will work or not other than trying to start the peering session.
D. There is no way to make BGP work across a firewall.
Answer: A
2. Spanning tree protocol calculates path cost based on what?
A. Interface bandwidth
B. Interface delay
C. Interface bandwidth and delay
D. Hop-Count
E. Bridge Priority
Answer: A

3. The ‘ip pim autorp listener’ command is used to:
A. Enable a Cisco router to “passively” listen to AutoRP packets without the router actively sending/forwarding
any AutoRP packets.
B. Allow AutoRP packets in the groups 224.0.1.39 and 224.0.1.40 to be Dense mode flooded out interfaces
configured as ‘ip pim sparse-mode’.
C. Enables the use of AutoRP on the router.
D. Configures the router as an AutoRP Mapping Agent.
Answer: B

4. Given the shown output, which statement is true regarding the router forwarding a packet to 192.168.32.1?

19. You have attempted to configure OSPF v3 between two routers over Frame Relay and your adjacency has
failed to establish. What is the problem?
A. You have failed to map the all routers multicast address to the DLCI
B. You have failed to map the solicited node multicast address to the DLCI.
C. You have failed to map the neighbor’s link local address to the DLCI.
D. You have failed to map the all routers broadcast address to the DLCI.
Answer: C

20. When determining your security policies for deploying Unicast Reverse Path Forwarding (uRPF) on your
network, which is NOT an action that uRPF can perform?
A. uRPF examines all packets received to make sure that the source address and source interface appear in the
routing table and match the interface where the packet was received.
B. uRPF checks to see if any packet received at a router interface arrives on the best return path.
C. You can have an ACL configured and combined with your uRPF configuration.
D. uRPF events can be logged by specifying the logging option for the ACL entries used by the Unicast RPF
command.
E. uRPF inspects IP packets encapsulated in tunnels, such as GRE.
Answer: E

21. What are the three types of LMI that can be configured to be used with frame-relay on a Cisco router?
(Choose 3)
A. Cisco
B. ANSI - Annex D
C. Q.931 - Annex B
D. Q.933 - Annex A
Answer: ABD

22. What does the Cisco Spanning Tree Root Guard feature provide in a bridged network?
A. It ensures that the bridge is elected as root bridge in the network.
B. It enforces the root bridge placement in the network.
C. It ensures that BPDUs sent by the root bridge are forwarded in a timely manner.
D. It ensures that all ports receiving BPDUs from the root bridge are in the forwarding state.
Answer: B

23. Which fundamental modifications, related to traffic forwarding, does MPLS introduce? (Choose 2)
A. IP lookup is done on every hop with the MPLS core.
B. IP destination routing is reduced to label lookup with the MPLS network.
C. For unicast routing, labels are assigned to FECs (i.e.: IP prefixes).
D. For multicast routing, labels are assigned to IPmc groups.
Answer: BC

24. Which of the following parameters are used to determine a FEC (Forwarding Equivalent Class)? (Choose 2)
A. IP Prefix
B. Layer 2 circuit
C. RSVP request from CE for bandwidth reservation
D. BGP MED value
Answer: AB

Free Down:Pass4sure CCIE 350-001
Free Down:Testking 350-001

Type	Exam Bible	New Questions & Answers	Latest Updated	Download link
	All Cisco 's Exam Pack	589	1 days ago	Download