Actualtests 642-432
642-432 : Cisco Voice Over IP Last Updated Tuesday, April 22, 2008 with 228 Questions
IP Communications Cisco Voice Over IP
Exam Number: 642-432 Exam
Associated Certifications: IP Communications Cisco Voice Over IP
Duration: 72 Q&As
Available Language(s): English
Exam Details
The Cisco Voice over IP 642-432 CVOICE exam is associated with the CCVP, Cisco IP Communication Support Specialist, and Cisco Rich Media Communications Specialist certifications. Candidates can prepare for this exam by taking the Cisco Voice Over IP (CVOICE) course. This exam assesses a candidate’s knowledge of how to implement and support data and voice integration solutions at the network-access level. Topics covered include basic IP Telephony operation, router configuration, support, troubleshooting, and integration with an existing PSTN network.
Free 642-432 Exams’s PDF Download
Free Actualtests offers free demo for 642-432 PDF(IP Communications Cisco Voice Over IP). You can check out the interface, question quality and usability of our practice exams . We are the only one site can offer demo for almost all IP Communications Cisco Voice Over IP.
Recommended Training about 642-432 exam PDF
The following courses are the recommended training for 642-432 exam PDF.
642-432 Q & A with Explanations
642-432 Audio Exam
642-432 Study Guide
642-432 Preparation Lab
642-432 Exam Preparation from Actualtests with FULL explanations include:
Comprehensive questions with complete details
Detailed explanations of all the questions
Questions accompanied by exhibits
Verified Answers Researched by Industry Experts
Drag and Drop questions as experienced in the Actual Exams
Questions updated on regular basis
These questions and answers are backed by our GUARANTEE.
Like actual certification exams our product is in multiple-choice questions (MCQs).
642-432 Exam: Actualtests’s IP Communications Cisco Voice Over IP PDF
The IP Communications Cisco Voice Over IP PDF for preparing for the 642-432 exam - Actualtests’s IP Communications Cisco Voice Over IP. Actualtests is your premier source for practice tests, and true testing environment. Nothing will prepare you for your next exam like a Actualtests. You find it all here at ciscoexams.org.
QUESTION 1
Which type of signaling is DTMF?
A. Supervisory
B. Route
C. Informational
D. Address
Answer: D
Explanation:
Start dial supervision is the line protocol that defines how the equipment seizes the E&M
trunk and passes the address signaling information such as dual tone multifrequency
(DTMF) digits.
Address Signaling
Address signaling typically represents the digits dialed (called party’s number). There are
two options used to pass address information. Either Pulse dial (rotary dialing) or Tone
dial (DTMF) can be used. The default for Cisco routers and gateways is DTMF.
QUESTION 2
You have set up a complex dial plan using translation rules. The following
translation rule has been configured.
What output would correspond to the test translation-rule command?
translation-rule 1
rule 0 ^0.. 215550210
rule 1 ^1.. 215550211
rule 2 ^2.. 215550212
rule 3 ^3.. 215550213
rule 4 ^4.. 215550214
rule 5 ^5.. 215550215
rule 6 ^6.. 215550216
rule 7 ^7.. 215550217
rule 8 ^8.. 215550218
rule 9 ^9.. 215550210
A. test translation-rule 1512
The replaced number: 21555021512
B. test translation-rule 1555
The replaced number: 55521555021
C. test translation-rule 1617
The replaced number: 61721555021
D. test translation-rule 1910
The replaced number: 21555021910
Answer: A
642-432
Actualtests.com - The Power of Knowing
Explanation:
New Delhi(2-digit indial range)
!— Only relevant “IOS translation rule” output is presented
!
translation-rule 1
!– The “1″ above is the tag for the set.
rule 0 ^0. 1011000
rule 1 ^1. 1011001
rule 2 ^2. 1011002
rule 3 ^3. 1011003
rule 4 ^4. 1011004
rule 5 ^5. 1011005
rule 6 ^6. 1011006
rule 7 ^7. 1011007
rule 8 ^8. 1011008
rule 9 ^9. 1011009
!
!– These rules replace the first digit of a 2-digit number with the corresponding
!– translation. The router looks for a 2-digit number starting with a leading [0-9].
!– The caret, “^” ensures the match only happens at the start of the digit string
!– rather than any occurrence in a digit string. This ensures the router makes the
!– translation only for the leading digits. By default, if an explicit match is made
!– on a digit (in this case the first digit) the router replaces it with the new
!– digits. Therefore, to keep the original numbering, the matched digit needs to be
!– replaced with the same digit at the end of the modified string. Once the call
!– comes in, the called number prepended with 101100 followed by the
!– original 2 digits.
!
voice-port 1/0:1
translate called 1
cptone IN
compand-type a-law
!
!– The translation rule is applied to the voice port where the
!– call comes in to the router. When a call comes in from the
!– telephone network towards the router, the called number
!– is translated before it is matched on any dial peers.
!
dial-peer voice 100 voip
destination-pattern 101100..
session target ipv4:main site IP address
ip precedence 5
dtmf-relay h245-alphanumeric
!
!– The VoIP dial peer needs to be configured to match on the new numbering plan
642-432
Actualtests.com - The Power of Knowing
This output was captured from the NewDelhi router which shows the translation rules
applied while dialing from the NewDelhi site.
NewDelhi- Output
!– It is possible to confirm the translation rules are working:!!NewDelhi#test
translation-rule 1 99!– Original called number is “99″The replaced number:
10110099!– Translated to 8 digits
QUESTION 3
What is the optimal end-to-end delay that should be achieved in a VoIP network?
A. 20 ms
B. 100 ms
C. 150 ms
D. 400 ms
Answer: C
Explanation:
Delay Specifications
QUESTION 4
Which three are supervisory signals? (Choose three)
A. busy
B. on hook
C. off hook
D. call waiting
E. ring
642-432
Actualtests.com - The Power of Knowing
Answer: B, C, E
Explanation:
1. Supervisory Signalling - electrical voltages and tones that can be heard are used to
signify call status as follows:
2. 1. On-hook - produces an open circuit which does not allow any signalling, only the
ringer can operate.
2. Off-hook - lifting the handset closes the circuit and allows the telephone switch to
send an audible dial tone to the receiver.
3. Ringing - the switch sends a ringing voltage to the destination telephone as
notification of an incoming call. Also an audible ringing tone is sent to the caller
telephone to indicate that the call is progressing. This tone takes the form of a
pattern called Cadence In Europe this Cadence takes the form of a double ring
(duration of 0.4s separated by 0.2s) followed by two seconds of silence, whereas in the
US it takes the form of two seconds of ring followed by four seconds of silence.
QUESTION 5
What is the E.164 numbering plan?
A. A proprietary PBX number plan.
B. The IETF North American number plan.
C. The European PBX standard telephony number plan.
D. The ITU worldwide number plan.
Answer: D
Explanation:
Numbering Scheme
The standard PSTN is a large, circuit-switched network. It uses a specific numbering
scheme, which complies with theITU-T international public telecommunications
numbering plan (E.164) recommendations. For example, in North America, the North
American Numbering Plan (NANP) is used, which consists of an area code, an office
code, and a station code. Area codes are assigned geographically, office codes are
assigned to specific switches, and station codes identify a specific port on that switch.
The format in
North America is 1Nxx-Nxx-xxxx, with N = digits 2 through 9 and x = digits 0 through
9. Internationally, each country is assigned a one- to three-digit country code; the
country’s dialing plan follows the country code. In Cisco’s voice implementations,
numbering schemes are configured using the destination-pattern command.
E.164 is an ITU-T recommendation which defines the international public
telecommunication numbering plan used in the PSTN and some other data networks.
QUESTION 6
On the MOS scale, what does a 5 represent?
642-432
Actualtests.com - The Power of Knowing
A. poor
B. fair
C. average
D. extra medium
E. excellent
Answer: E
QUESTION 7
Which of the following best describes the main difference between G.729 and
G.729a?
A. G.729 has higher complexity.
B. G.729 requires a higher bit rate.
C. G.729a has built-in echo cancellation.
D. G.729a has improved speech performance.
E. G.729a is designed for use with 3DES encryption
Answer: A
QUESTION 8
What type of signalling is used for a circuit transmitted within the same channel as
the voice?
A. PCM
B. SS7 Signalling
C. In-line Signalling
D. Common Channel Signalling
E. Channel Associated Signalling
Answer: E
QUESTION 9
You are the Voice technician at Certkiller .com. The Certkiller network uses VoIP.
Your newly appointed Certkiller trainee wants to knowwhat the disadvantage of
using VoIP rather than VoFR or VoATM are.
What will your reply be?
A. Data can arrive out of sequence.
B. Networks are complicated to design.
C. Data units can arrive out of sequence.
D. Network failures are not automatically found.
Answer: C
642-432
Actualtests.com - The Power of Knowing
QUESTION 10
You are the network engineer at Certkiller .com. You have configured real-time call
control processing on the Certkiller VoIP network. You want to verify this
configuration.
What command should you use?
A. debug voip rtcp
B. debug call control
C. debug voip ccapi inout
D. debug voip call control
E. debug voice call control
Answer: C
Free download：pass4sure 642-432
Free download：testking 642-432
TestKing - TestKing.com Help you pass Cisco exams
Pass4sure -Pass4sure.com The Worldwide Renowned Cisco Certification Material Provider .
Random Posts
[...] Cisco Voice Over IP”, also known as 642-432 exam, is a Cisco certification. Preparing for the 642-432 exam Searching 642-432 Test Questions, 642-432 Exam, 642-432 [...]
[...] Voice Over IP”, also known as 642-432 exam, is a Cisco certification. Preparing for the 642-432 exam? Searching 642-432 Test Questions, [...]